This is a Factory OEM (Original Equipment Manufacturer) Chevrolet 4 Button keyless entry remote, aka "key fob".

Factory OEM key fob. Comes with uncut key. You will receive one of the listed interchangeable part numbers.

Chevrolet

• 2013 Chevrolet Corvette
• 2012 Chevrolet Corvette
• 2011 Chevrolet Corvette
• 2010 Chevrolet Corvette
• 2009 Chevrolet Corvette
• 2008 Chevrolet Corvette
• 2007 Chevrolet Corvette
• 2006 Chevrolet Corvette
• 2005 Chevrolet Corvette

Quick Learn Method:

IMPORTANT: This procedure is not available when the maximum number of 4 fobs have been programmed. If 4 key fobs are programmed to this RCDLR and this method
is attempted, the driver information center (DIC) will display, MAX FOBS LEARNED and the programming procedure will exit.

This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed
using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicle's mechanical key.

1. The vehicle must be off.

2. Open rear compartment

3. Place a known key fob within the interior of the vehicle.

4. At the rear of the vehicle, insert the vehicle key into the rear compartment lock cylinder,located above the license plate and cycle the key 5 times within 5 seconds.

5. The DIC will display: READY FOR FOB X (X = fob 2, 3, or 4).

6. Place the replacement key fob in the glove box fob pocket with the buttons facing right.

7. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.

8. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion
of the ignition switch to exit programming mode.

9. Operate the active portion of each key fob in order to verify correct system operation.

Only keyless access transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to four transmitters programmed to it.

Programming with a Reconized Transmitter

A new transmitter can be programmed to the vehicle when there is one recognized transmitter. For vehicles sold in Canada, two recognized transmitters are required to program a new transmitter.

1. The vehicle must be off.

2. Both the recognized and new transmitters must be with you.

3. Insert the vehicle key into the key cylinder located above the license plate.

4. Open the hatch/trunk.

5. Turn the key five times within five seconds.

6 The DIC displays READY FOR FOB #2, 3, or 4.

7. Place the new transmitter in the glove box transmitter pocket with the buttons facing the passenter side.

8. A beep sounds once programming is complete. The DIC displays READY FOR #3 or 4, or MAXIMUM NUMBER OF FOBS LEARNED.

9. Tp program additional transmitters, repeat Step 7. Press Acc. on the ignition switch if programming is complete.

10. Press Unlock on each newly programmed transmitter to complete the process.

Programming without a Recognized Transmitter

This procedure requires three ten minute cycles to complete the programming process. United States owners are permitted to program a new transmitter to their vehicle when a recognized transmitter is not available. The Canadian immobilizer standard requires that Canadian owners see their dealer/retailer for programming new transmitters when two recognized transmitters are not available.

1. The vehicle must be off.

2. Place the new transmitter in the glove box transmitter pocket with the buttons facing the passenger side.

3. Insert the vehicle key into the key cylinder located above the license plate.

4. Open the hatch/trunk.

5. Turn the key five times within five seconds.

6. The DIC message displays OFF-ACCESSORY TO LEARN.

7. Press Acc. on the ignition switch.

8. The DIC reads WAIT 10 MINUTES and counts down to zero.

9. The DIC displays OFF-ACCESSORY TO LEARN again.

10. Press Acc. on the ignition switch.

11. Steps 8, 9, and 10 will be repeated two more times.

12. A beep sounds and the DIC reads READY FOR FOB #1. All previously known transmitter programming has been erased.

13. A beep sounds once programmin is complete. The DIC displays READY FOR FOB #2.

To program additional transmitters, take transmitter 1 out of the transmitter pocket and place transmitter 2 in the pocket. Up to four transmitters can be programmed. The DIC then displays MAXIMUM NUMBER OF FOBS LEARNED and exits the programming mode.

Press Acc. on the ignition switch to complete the process.

14. Press Acc. on the ignition switch if programming is complete.

15. Press Unlock on each newly programmed transmitter to complete the process.

OEM Key Fobs:

We are proud to offer true OEM key fobs direct to you at up to 80% off dealer prices. There is a catch though, so here it goes:

You need to know the only way to get a NEW OEM key fob is to go to a dealer or authorized reseller of OEM parts, and you will pay dealer prices if you do this and spend hundreds of dollars.

The key fob you are going to purchase from us is used or as we like to say "previously loved". We recycle OEM key fobs and put them through a rigorous refurbishing process so we can guarantee our products and offer them at a reasonable price along with saving the environment. Oh, and we are not robbing you of your hard earned dollars like the stealership does. So if you are good with all of this what are you waiting for? Make your life easier, order a key fob from us and save the world!